I wanted to get a couple of the Vesper rewards
Whats the difference between Ter Mur and Tram/Fel. It looks for tiles containing the word "TREE".
Gimlet, at the moment no it won't, but a very simple change and I guess it could do.
Will have a look later at it for you.
The difference is that from Easyuo you get ZERO/nill/nada tile information for TerMur. So you/it will not find any trees via tile scanning.
When it tries to chop at the secure, don't stop the script. Just let it run it out.
It will get bored of your house and move on.
But as a guess I'd say your carrying too much weight.
Did you re-download the script?
if You_can't_use_ in #sysmsg
{
break
}
if Target_cannot_be_seen in #sysmsg
{
break
}
if too_far in #sysmsg
{
break
}
until not_enough_wood in #sysmsg
return
Set %GateType KEF_OTF_JEF
SUB GetRidOfMyGate
if %Travel_Method = GA
{
IgnoreItem reset
Set #TARGCURS 0
FindItem %GateType
Repeat
{
if #FindCnt > 0
{
For !tmp 1 #FindCnt
{
Set #FindIndex !tmp
if #FindDist > 10
{
IgnoreItem #FindID
}
ELSE
{
; Wait for Mana to Cast Lvl 5 Spell
While #Mana < 14
{
}
While %NEXTDispelTime > #SCNT
{
}
;Cast Dispel Field
Set %NEXTDispelTime #SCNT + 4
Event Macro 15 33 ; Dispel Field
Wait 30
Target
Set #lTargetID #FindID
Event Macro 22 0
Wait 2s
}
}
}
;Check for other Gates around
FindItem %GateType
}
Until #FindCnt = 0
}
RETURN
It is most likely trying to continue chopping from your last know point because your recall book hadn't recharged, or it simply failed to recall. Don't stop the script, let it sort it's self out. It's written to not stop just because it can't find any trees, it should simply go to another rune eventually. What is the system message produced when your at your secure and it tries to chop?? The script is designed to search for several system messages whilst chopping:Code: [Select]if You_can't_use_ in #sysmsg
{
break
}
if Target_cannot_be_seen in #sysmsg
{
break
}
if too_far in #sysmsg
{
break
}
until not_enough_wood in #sysmsg
return
If it's non of those, then it won't stop. So I need a little more information on your part.
if You_can't_ in #sysmsg
This will incorporate the new and old #sysmsg's"You can't do that" wasn't in my list :S
Now been changed to:Code: [Select]if You_can't_ in #sysmsg
This will incorporate the new and old #sysmsg's
Also, Gimlet, added dispel sub for you.
Although I think I've found the issue over-all, when implimenting TM's travel subs, I think I missed the return to tree's after dropping off wood.
Let me know if it works, I haven't have time to test the updates as I'm frantically trying to get mace and shield glasses :p
Try this one:
FYI this script isn't finished, you have to select ALL LOGS for it to work correctly. Don't think it counts them or anything. I'm not officially releasing it, but it's there if you want it.
Over-all, it's faster running the two things seperately because otherwise your wasting time chopping 20 oak boards, as opposed to the 250 when script is dedicated to chopping logs into boards.
Been slowly working on a way to get it to be selective, and display properly. Not to far off, so look out for the propper release of my log splitter.
sub find_tree
menu Window Title Reaper , #spc , - , #spc , Status: Scanning.....
tile Init
for %TR_x 2 -2
{
for %TR_y 2 -2
{
set %TR_xpos #charposx + %TR_x
set %TR_ypos #charposy + %TR_y
tile CNT %TR_xpos %TR_ypos
for %TR_cnt 1 #tilecnt
{
tile GET %TR_xpos %TR_ypos %TR_cnt
if TREE in #tilename
{
gosub chop
menu Window Title Reaper - Status: Scanning.....
}
}
}
}
return
I see no script here to try?
I see no script here to try?
Been attempting to use this script on OSI, it just gets stuck at scanning. I believe I have everything set up properly. It recalls to the first chop location then just sits and does absolutely nothing.
I have been using this and decided to add another book since i am only using 3...I cannot for the life of me figure out what to change to make it walk me through setup again...i have tried reading through it and changing what i thought it needed but no luck....can someone please explain what i need to do to make it run me through setup once again.
;==================================
; Instructions:
; Simple, have 5 rune books, 4 contain runes to trees, 1 contains
; a rune to your house (IN SLOT ONE!!!)
; If you want to get around setting it up each time, work it out
; for yourself, it's not hard. Otherwise you deserve the lengthy
; setup.
; Note:
; If you only have one book of trees, simply target that book 4 times.
;==================================
set %TR_debug 0
;==================================
; Remove the ";" to reset the script should you wish to change any of the setup
; gosub TM_NGFS_DeleteName TheReapers_Log_Harvester
; halt
You need to add the old mul files back into your uo folder. Download and these to your uofolder and it should fix your issues. I have never needed to do anything to the registry when using these. http://www.scriptuo.com/index.php?topic=12768.0
You need to install ( copy) the old mul. file into the UO directory. They should be somewhere around the forum
here the Link http://www.scriptuo.com/index.php?topic=14877.0
Just copy all those file in the end folder. C:\Program Files (x86)\Electronic Arts\Ultima Online Classic
You need to install ( copy) the old mul. file into the UO directory. They should be somewhere around the forum
here the Link http://www.scriptuo.com/index.php?topic=14877.0
Just copy all those file in the end folder. C:\Program Files (x86)\Electronic Arts\Ultima Online Classic
I really appreciate the direct link. I downloaded the ZIP folder, I clicked extract all, I selected C:\Program Files (x86)\Electronic Arts\Ultima Online Classic.
I restarted the client and EUO (Run as admin). I play the script, it recalls me to the first spot to LJ and it still gets stuck on Status: Scanning....
I am pretty new to this stuff, I am wondering if I might be missing something simple? I am searching other forum posts regarding these .mul files and I haven't come up with anything.
If you have any suggestions I would greatly appreciate it!
trying to use it dont know how this works